Search

In Stock

MINIFOR laboratory fermentor and bioreactor

The fermentor had to take up minimum space on the bench, but with good access to all parts. Several fermentors should, when placed side by side, be suitable for the optimization of growth parameters of the culture or optimization of bio-transformations, etc.

The space requirement of the MINIFOR fermentor-bioreactor with working vessel and the control unit is: 22 cm x 38 cm x 40 cm (W x H x D).

Spesification :

Power: Universal power supply for mains 100-245 V AC/50-60Hz, 560W, CE conform
Dimensions: 22 x 40 x 38 cm (W x D x H)
Display: LCD 4 x 40 digits with backlight illumination
Fermentor vessel: Pyrex glass with 6 to 8 side necks; 0.3, 0.4, 1, 3, 7 liter vessels
Temperature control: High efficiency 150 W infrared (IR) radiation heat source with gilded parabolic reflector
Regulation: from 5°C over RT to 70°C
Measurement: from 0 to 99.9°C in 0.1°C steps
Precision: +/- 0.2°C (0 to 60°C)
Sensor: Pt 100 incorporated in the glass electrode of the pH probe
pH control: sterilisable pH electrode pH 0-14 with automatic temperature correction, two-point semiautomatic calibration and Variopin connector
Resolution: 0.01 pH unit
Precision: +/- 0.02 pH unit
pO2 control: sterilisable Clark type oxygen sensor with fast response, automatic temperature correction, two-point semiautomatic calibration, dissolved oxygen (DO) control through regulation of the airflow rate
Range: 0 to 25 mg oxygen/ l, in 0.1 mg/l steps
Air flow: 0 to 5 l/min in 0.01 l/min steps, measured by precise mass flow meter, linearity +/- 3%, reproducibility +/- 0.5%
Control: proportional valve controlled by microprocessor
For supplied air pressure: 0.05 – 0.2 MPa (0.5 – 2 atm)
Agitation: 50 W Vibromixer 0 to 20 Hz (0 to 1200 rpm) in 0.1 Hz steps (6 rpm) with 1 or more stirring discs; Sterility similar to magnetic coupling
Selectable parameter ‘X’: an additional parameter can be controlled by the instrument (foaming control, weight (for continuous cultures), pCO2, redox potential, conductivity, optical density, etc.); with standard 0-10V or 0-20mA output
Ports / side necks: One large quadruple sampling or additions port with four needles with LAMBDA PEEK double-seal connections, used for sampling, inoculation, antifoam, feeds, harvest, addition of correction solutions etc., additional double ports are available.
Pumps: up to 4 independent pumps (PRECIFLOW, MULTIFLOW, HIFLOW or MAXIFLOW) with speed variation from 0 to 100 % can be used with MINIFOR lab fermenter-bioreactor
Gas flow control: In addition to pumps, several electronic flow controllers with flow rate ranges of 0-5 l/min (MASSFLOW 5000) or 0-500 ml/min (MASSFLOW 500) can be used for the controlled addition of gases (e.g. N2, O2, air, CO2) in cell cultures; freely configurable gas station module
Working temperature: 0 – 40 °C
Working humidity: 0 – 90 % RH, not condensing
Weight: 7.5 kg
PC control: complete PC control and data processing using the fermentation software FNet (for up to 6 MINIFOR fermenters) or SIAM (for an even higher number of instruments)

Bestsellers

Special Application Fume Hoods

PVC and stainless steel hoods for use with perchloric acid, acid digestion, and radioisotopes.

Class II, Type B2 (Total Exhaust) Biosafety Cabinets

These total exhaust cabinets protect the user, product and lab. They’re designed to be hard-ducted to the outside, exhausting 100% of the HEPA-filtered air outside the lab.

MODEL 3000MP ULTRASONIC HOMOGENIZER

The Model 3000MP Ultrasonic Homogenizer delivers up to 300 watts of ultrasonic disruption with precision control from a microprocessor and a graphical user interface displayed on a large LCD display. The Model 3000MP offers all the advanced engineering features necessary to create a total system for ultrasonic disruption. The compact vertical footprint is ideal for processing samples with volumes less than 250 μl with the Cup Tip and volumes ranging from 250 μl to 2000 ml with a wide selection of titanium tips.

-86C Classic ULT Freezer

ANTECH -86℃ ULT freezer is designed with single compressor auto-cascade refrigerant system. The key features are realiable temperature, fast cooling down, low engery consumption.The temperature controller is easy to operation which reduces the failure risk of complex control.The interior is made of #304 stainless steel for durable use and easy cleaning.ANTECH ULT freezer can reassure a stable ultra low temperature storage condition to store germs, erythrocytes, leucocytes, viruses and many other biological materials. Installations can be found in research institutes, pharmacy industry, clinical labs, blood banks and laboratories in electronic & chemical plant

MVE SC Series

Over the past 50 years, our product designs have improved through end-user input and evolved into a unique selection of units. The SC Series is designed for the user who has small capacity needs, but requires long-term storage and low liquid nitrogen consumption in a convenient lightweight package. Features Include:
  • Designed for large capacity storage
  • Low liquid nitrogen consumption
  • Convenient lightweight package

8010G & 8010S

The bases on all 8010/8011 series laboratory blenders have epoxy coated motor housing and are complete with either a Stainless Steel container (ES) or Heat Resistant Glass container.

Back to Top
Product has been added to your cart